top of page
Search

Have You Tested Your Heating Yet? Checks to Make Before the Cold Weather Arrives

Writer: FlameFlow
FlameFlow
Oct 25
3 min read

It is better to discover a heating problem now than on the first properly cold morning of the year.


If your heating has been switched off or used less during the warmer months, running it briefly can help identify problems before your boiler and radiators are working hard every day.


Here are some simple checks you can make safely at home.



Turn the Heating On Before You Need It


Switch the heating on for around 10 to 15 minutes and check whether the boiler starts normally.


Listen for unusual noises and look at the boiler display for any warning lights or fault codes.


If a fault code appears, take a photograph or write it down. This can help an engineer understand the problem before attending.



Check the Thermostat and Heating Controls


Make sure the thermostat is set above the current room temperature so it is actually calling for heat.


Check that:


• The thermostat display is working


• The correct programme or schedule is selected


• The boiler responds when the temperature is increased


• Any wireless thermostat is communicating with the boiler


A flat battery or an incorrect programme setting can sometimes look like a boiler fault.



Check Each Radiator


Allow the heating to run, then carefully check whether each radiator begins to warm up.


Look out for:


• A radiator that remains completely cold


• Cold areas at the top


• Cold areas at the bottom


• One room warming much more slowly than the others


• Unusual noises from the radiator or pipework


A radiator that is cold at the top may contain trapped air.


A radiator that is cold at the bottom can sometimes be linked to sludge or poor circulation within the heating system.


If several radiators are affected, the problem may be wider than one individual radiator.



Check the Boiler Display and Pressure


Look at the boiler pressure gauge or digital display.


The correct pressure range can vary between boilers and heating systems, so check the manufacturer’s instructions for your model.


If the pressure keeps dropping, do not simply continue topping it up without finding out why.


Repeated pressure loss can be linked to a leak or another problem within the heating system.



Look for Signs of Leaks


Check around visible pipework, radiators and valves for:


• Drips


• Damp marks


• Corrosion


• Staining


• Water underneath the boiler or radiator valves


Even a small leak can gradually lower the pressure in the heating system.


Do not remove the boiler casing to look for a leak. Work inside a gas boiler should only be carried out by a suitably qualified Gas Safe registered engineer.



Check Your Hot Water


If you have a combi boiler, run a hot tap and check whether the water becomes hot normally.


Pay attention to:


• Water taking longer than usual to heat


• The temperature changing unexpectedly


• The boiler displaying a fault code


• Unusual noises while the hot water is running


Intermittent hot water can be an early sign that something needs checked.



Think About When the Boiler Was Last Serviced


Regular servicing gives a Gas Safe registered engineer the opportunity to check the condition and safe operation of the boiler.


It can also help identify developing problems before they become more serious.


An annual boiler service is generally recommended.


Late summer or early autumn is a sensible time to arrange one because it gives you time to deal with any problems before the heating system is under greater demand.



When Should You Contact a Heating Engineer?


Arrange an inspection if:


• The boiler displays a recurring fault code


• The pressure repeatedly drops


• Several radiators are not heating properly


• You hear unusual banging, whistling or vibrating noises


• There are signs of a leak


• The boiler repeatedly shuts down


• You have no heating or hot water


Never remove the boiler casing, bypass a safety control or attempt gas work yourself.



Local Heating Help from FlameFlow


FlameFlow is based in Erskine and provides boiler, heating and plumbing services across Renfrewshire, Glasgow and surrounding areas.


Testing your heating before the colder weather arrives gives you time to deal with a problem before you depend on the system every day.


If something does not seem right, contact FlameFlow with your postcode, boiler make and any fault code showing.


Call, text or WhatsApp us on 07795 221357.

 
 
 

Comments


bottom of page